1
Instruction Manual/Instrucciones
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
MOUNTING YOUR FIXTURE
NOTE: This fixture is intended to be conduit connected
to a properly installed and properly grounded metal
weatherproof junction box (not included). All conduit
connectors, conduit, and junction boxes (sold separately)
should be UL Listed suitable for wet locations.
1. Using the pattern on the box, mark and drill holes
for mounting.
NOTE: Mount this fixture in an upright position.
2. Install the two bottom mounting screws (C) first,
leaving enough room between the mounting
screws and the mounting surface to accommodate
mounting the fixture.
3. Screw the top mounting screw (C) into the predrilled
hole and back the screw out. This will leave the hole
threaded and make installation of the fixture easier.
4. Remove access cover (B) from the parts bag.
5. Install the first conduit connector and conduit
(sold separately) into the access cover (B).
6. Feed supply wires into conduit and make wiring
connections as described in “Wiring Your Fixture”.
7. Attach access cover (B) to the light fixture (A)
using the two access cover mounting screws
provided (F) (Fig. 1).
NOTE: Make sure all wiring is placed into the arm
prior to tightening the access cover screws.
8. Using the three mounting screws (C) provided, bolt
the housing (A) to the mounting surface.
9. Connect second conduit and conduit connector at
the junction box (Fig. 1).
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Adjustable wrench
• Drill with 3/16 in. drill bit
• 1/2 in. diameter flexible conduit (if applicable, length depends on application)
• 1/2 in. watertight conduit connectors (if applicable)
• Wire connectors
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Read and follow these instructions.
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• UL for wet location use.
• Read and follow these instructions.
• Disconnect at fuse or circuit breaker before installing or servicing.
• Disconnect power and allow fixture to cool before changing bulb or handling fixture.
• Edges may cut. Handle with care.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Upside down installation can result in overheating or accumulation of water in fixture.
Install right side up.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation. Under Part 15 of the FCC Rules, any changes or modifications to
the motion detector described in this instruction sheet that are not expressly approved
by Cooper Lighting, LLC could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
AL2050LPCBZ
(Bronze/Bronce)
AL2050LPCGY
(Gray/Gris)
A. Light fixture
Accesorio
ENGLISH
WARNING
B. Access cover
Cubierta de
acceso
C. (3) Mounting screws
(3) Tornillos de montaje
D. Light sensor
Detector de luz
E. (3) Wire connectors
(3) Conectores de cables
1
Conduit
Conduit
connector
Junction
box
A
B
F. (2) Access cover mounting screws
(2) Tornillos de la cubierta de acceso
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals